If you have a twin-drive boat, you can place the device between the drives. It's all do to with the angle of the dangle. This will prevent any screeching and scratching between them, as well as water infiltrations. Insert the transducer in and secure it with a bolt and nut. 6mm bolts and 6 nuts, a silicone sealant, 6 rubber and metal washers, plastic conduit and terminal connectors. It shouldn't be that hard to do. Transducer pole mounts for pontoon boats. Yes, if you mount a transducer too low, it will trigger turbulence and air bubble formation around the transducer, as well as rooster tail formation behind the transducer. Option 1: Use the fuse box. So the ideal transducer mounting height on the transom is with the bottom surface of the transducer just slightly protruding below the bottom of the boat (see diagram above). 7 meters) of electrical wire for positive and negative (red and black). Set the cables under your boat's floorboard and connect them to the terminals in the fishfinder console. All in all, you'll only need an hour or so to complete all the steps necessary. Similar read: Installing a fish finder on the bow of your boat.
Take a look up under the console to check for anything that could get in the way, paying particular attention to the underside of where you are going to be mounting. So I had to order an extension cable so my cord would reach halfway the length of my boat and all the way across to the driver's console. Drill two holes at the bracket. Understand the location of the transducer and fishfinder monitor. Is there a better option?? Things You Need for this Tutorial. Next, select three or four of the pre-drilled holes where you'll put bolts through. However, an alternative option is to use a transducer mounting pole, which was specifically designed for live sonars, and can be positioned at the front of your boat similar to a trolling motor. Pontoon pinging is a little different. In-hull transducers are ideal for watercraft with a maximum deadrise angle of 30 degrees and high-performance boats. Warning: Be CERTAIN that all of the metal parts you buy are stainless steel!
You can install the transducer under the pontoon in a place close to the console. For aesthetic reasons, as well as to prevent rubbing between the wires and the sharp edges of the hole, you can use a rubber grommet. Yet, they usually instruct you to tie the power into the battery, which is usually at the back of the boat by the engine. Many people put their monitors on their consoles to gain visuals and easy access while searching for an excellent fishing spot. The best transducer mounting height is at the bottom edge of the transom, with the lower surface of the transducer protruding about 1/32 to 1/16 inches below the bottom of the boat. Transducer placement. On my 2021 Bass Buggy 16 I mounted the transducer for my Humminbird on the bracket supporting my live well pump that is located on the rear of the port pontoon. Also, placing the transducer too close to a livewell pump (if you have a livewell on your pontoon boat) can cause interference in the signal. Then simply connect the bracket with nuts and bolts on the console. So, go ahead and install it and enjoy a nice fishing trip. The greater the distance of cord, the more likely you are to not have enough signal strength to send the data. The transducer wire was a bit loose and I just had to push it back in.
Then, attach the transducer mount that came with your fish finder through those two holes and secure it with a bolt and nut. The manufacturer had the original wiring attached to the toons and crossbars. The original power cord is often too short and, if that's the case, you'll have to buy a longer cord (20' on average). Once deep enough, you can proceed to drill clockwise or forward. Transducer mounting bracket for pontoon boats. Too much distance between the monitor and transducer may result in a signal that is too weak and there may be electrical interference. A transducer is the piece of kit that sends and receives the echo data that appears on the fish finder screen, using sonar technology. They are used to detect non-visible hazards in the water, work out the depth of the water, and detect fish targets and objects such as fallen trees. The side of the transom with the downward stroke of the prop has less turbulence than the side with the upward stroke, which is why it is the best transducer mounting location. Also, make sure that ALL METAL PARTS ARE STAINLESS.
You can opt not to wipe off the excess substrate because it can serve as an additional layer of protection against water ingress. Step 4: Mount & Install the Fish Finder Monitor. But, it will depend on the console in your pontoon. Installing a garmin transducer on a pontoon boat. Fish finder kits come with all the materials needed for installing them in a traditional V-hull boat, but they won't have all the materials you'll need for installing on a pontoon boat. You can refer back to step 1 to see my views on the optimum placement. Fish finders locate fish underwater, allowing anglers to make a more accurate casting.
"I have a 2008 Crest 20-footer, but both the pre-installed fish finder and the fuel gauge don't work. Check it before shopping so you know what kind of connectors you need. If it's too low, it will get the full force of the water under the toon. And when you lay down the cable, make sure to keep it away from any other wires or electronic devices that can cause interference. I am passionate about water sports and technical fields, so combining both makes me interested in making contents about boat accessories. Step 5: Hook into the Power. Tool steel, spring steel, Damascus steel, it doesn't matter; just make sure it's positively stainless. In most cases though, your fish finder should not have a problem keeping up. Be sure the hole is large enough so the connector on the transducer cord can pass through. Get a drill bit and drill through the mounting bracket in two places. Sand the hole to ensure a smooth surface, ensuring optimal sealant adhesion. Keep in mind when placing the transducer that it's best to place it far away from electrical interference from being too close to another wire.
Rubber grommet for cords to go through the console (optional). If it is difficult to set the cables because of obstacles in your watercraft, you might want to check the manufacturer's recommendations to see if you can cut the wires. Here's the list: - 6 stainless steel bolts. Don't worry, this won't hurt your pocket book nearly as bad as your fish finder purchase. I was careful not to over-tighten the lower bolt, which might break the transducer's plastic housing. Seems like overkill. A 20-minute trip to the hardware or auto parts store will likely save you a four-hour job a few years from now.
Based on their mount, there are four types of transducers: thru-hull, transom mount, in-hall, and trolling motor. Mount the transducer. The second thing is to make sure that there are no electrical interferences. It has a nylon, threaded bronze, or stainless steel shaft passed through the hull's bottom. You're never too waterproof. This made it incredibly easy to tap into. You may want to get a rubber grommet to cover this hole so that it looks nice. Set the wires to run through your boat and into your fishfinder console.
I am the guy at the boat ramp that gives you dirty looks when you are a complete idiot and too stupid to know it. This strap-on tube transducer mount is universal and fits pretty much any transducer out there. Place the transducer base plate on the surface, positioning the mounting ports over the holes on the boat. When mounting the fishfinder, set the bracket in place and place it wherever you wish to. What's more, you will definitely experience signal loss on too long a wire. You could try adding a battery that is dedicated to electronics. Pro Tip: Ensure the hole forms a 90-degree angle with the waterline.