What was the engineers reasoning? 2001 SR-5... bought 11/ 6/21.... 2000 SR-5 moded, lifted, e locker, other cool stuff, totaled 10/20. Damaged or Missing Parts.
If you also need 4 bolts, then you have two choices: - Best: If you'd like to use the (better) "Black" bolts (w/washer) to secure the LBJ to the lower control arm (LCA), purchase LBJs and bolts separately: - Good: A kit that includes "Green" flanged bolts to secure the LBJ to the lower control arm (LCA), are sold as part numbers - L: 43340-39585; R: 43330-39815. ARP bolts 8740 chromoly = 180-210ksi. Starter mounting bolts: 29 ft-lbs. Torque specs for 05 double cab 2wd. Lower ball joint nut. Note: You will end up with a stronger LBJ - regardless of rubber dust cover use - by using the black bolts. With these bolts removed the entire brake system can be placed to the side, be weary of the brake hose that connects to the. Transmission mount to crossmember: 14 ft-lbs. You may not post attachments. I'll even throw in four bolts, a couple castle nuts, and one cotter pin for the same low, low price! And torque the endlink nuts to 22 ft-lbs and then torque the bracket bolts to 19 ft-lbs as well.
The customer is responsible for import taxes and fees on international shipments. Oh thanks, I missed that link. Hand tightened you can line up the bottom bolt hole and install the bolt and hand tighten its nut. Once it feels like they have been tightened to about 100 ft-lbs they will be good to go. 10-22-2020, 03:42 PM. 1st gen tacoma lower ball joint torque specs size. If you do lots of bumpy, off-road style driving, every 30-50, 000 miles is a reasonable interval to change this part of your truck, in order to prevent a catastrophic failure. With all of the fasteners loosened you can use a pickle fork to remove the joint part from the lower arm. Rear end plate: 14 ft-lbs.
I guess to save money? Thanks for sharing this. Additionally, the "green" flanged head bolts should only be used once, while the "black" bolts can be reused several times. This is recommended reading due to the importance of LBJs, but if you'd rather not read it, the conclusion was that the best bolts are properly torqued (37 ft-lbs) black bolts (90119-10933) that were introduced for later models (01-04 Tacoma, 01-02 4Runner) when the LBJ dust boot was added. On the Toyota Tacoma there are two control arms being the upper and lower control arms. Before you can access these bolts you will need to jack the vehicle up and remove the. '17 Chevy Volt Premier. Once the bolts have been removed you can take off the hub. Backing plate to axle housing: 50 ft-lbs. 1st gen tacoma lower ball joint torque specs and gear. Location: Raleigh, NC. Can be moved out of the way. I replaced them with the older style bolts immediately.
In fact, it all went so quickly that I only snapped a couple photos. To replace the front shocks on the Toyota Tacoma you will need to lift the vehicle up into the air and start by removing the tire on the side you want to replace. With that removed we can now remove the bolts and nuts. Shift lever retainer: 29 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ). No returns on items that have been damaged or installed. Flywheel to crankshaft bolts: 65 ft-lbs (2RZ), 19 ft-lbs + additional 90 (3RZ), 63 ft-lbs (5VZ) ~USE LOCTITE~. 2nd gen tacoma lower ball joint torque specs. These bolts are torqued to 37 ft-lbs. The email must also include your order number as well. A stud connection is nearly always superior to a bolted connection. The different LBJ bolts and why it's important, Prado 90 Series Mighty 90s Forum. Shock absorber to frame: 53 ft-lbs. The shipment can be delivered to a home or business. Shipping & Delivery.
Starting with the lower bolt we simply remove the nut from one side and then. Our suspension systems are not to be modified from its original design in any way. At this point, you can simply lift the hub assembly up and out of the way, in order to remove the old LBJ from the LCA. First off, my truck is set at 2. Air Intake Chamber: 15 ft-lbs (2RZ/3RZ), 13 ft-lbs (5VZ). The lower ball joint nut gets tightened down. Each of these options include exactly the same Lower Ball Joints. Just joined the list of people with failed lower ball joint bolts. Our customers most Frequently Asked Questions A-arm / Ball Joint install. Personally, I tend check prices on all of these and then purchase the cheapest L and R option, depending on whether I am replacing the bolts as well. Guides are intended to assist in each procedure to help diyers with the job. Inner tie-rod to rack: 76 ft-lbs.
5" lift and it "tops out" a lot (full droop over speed bumps and things of the like off-road). Dirt King Fabrication is not responsible or liable for any accidents, injuries or deaths that may occur from use of any products offered. Hold the part onto the vehicle. Here's the part numbers for the two different style bolts. 1ST Gen Suspension Torque Specifications. Access all special features of the site. "Black" Washer LBJ Bolt (90119-10933). Dirt King Fabrication will do everything possible to resolve the issue as quickly as possible. From a tools perspective, I mostly ended up using several sockets, a ball joint separator, and my impact and torque wrenches: - Misc sockets (set).
All products sold or manufactured by Dirt King Fabrication are intended for off-road use only. Pressure plate to flywheel: 14 ft-lbs. Can someone with parts and bolts in hand upload some reference images? Gets tightened down to 80 ft-lbs. The #90080-10066. bolts are suppose to be torqued to 59 ft-lbf. Toyota Tacoma Tie Rod Change/Removal.
Yeah, happened thankfully going 20 miles an hour right after hitting a pothole. Rear main oil seal: 9. From here you can torque the upper nuts down to 47 ft-lbs. Frequently Asked Questions. It would also be great to see pictures of the bolt heads and markings... we should be able to reference the bolt class from the Toyota manual to get rated proof strength and figure out what the torque values "should be". Another idea no one has mentioned yet is to replace the bolts with high strength studs and flange nuts.
If you receive damaged parts or are missing parts leave a note on the bill of landing and sign it. Now, with access to the hub assembly, remove the 4, 14mm bolts that secure the LBJ to the hub. Once the tire is off you can now access the old tie rod and remove it for replacement. If the shipping carrier losses your package please contact Dirt King Fabrication. 25 bolts about 30mm long. Unfortunately, we do not have much control over this situation and must wait for the carrier to process the claim. Location: Pasadena, CA. I knew there were two different style bolts already. Install the old 22mm castle nut (19mm on a 4Runner) that secures the outer tie rod end to the LBJ and hand tighten. Lug nuts: 83 ft-lbs. OME2906/Toyota OEM rears with 2004 Tacoma Dual Rate Fronts on Bilstien 4600s. The old bearing can be removed by taking out the.